One Hat Cyber Team

Edit File: VDSL-LINE-EXT-MCM-MIB

VDSL-LINE-EXT-MCM-MIB DEFINITIONS ::= BEGIN

IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
transmission,
Unsigned32                      FROM SNMPv2-SMI         -- [RFC2578]
RowStatus                       FROM SNMPv2-TC          -- [RFC2579]
MODULE-COMPLIANCE,
OBJECT-GROUP                    FROM SNMPv2-CONF        -- [RFC2580]
vdslLineConfProfileName         FROM VDSL-LINE-MIB;     -- [RFC3728]

vdslExtMCMMIB MODULE-IDENTITY
   LAST-UPDATED "200504280000Z" --    April 28, 2005
   ORGANIZATION "ADSLMIB Working Group"
   CONTACT-INFO "WG-email:  adslmib@ietf.org
         Info:      https://www1.ietf.org/mailman/listinfo/adslmib

Chair:     Mike Sneed
                    Sand Channel Systems
         Postal:    P.O. Box 37324
                    Raleigh NC 27627-732
         Email:     sneedmike@hotmail.com
         Phone:     +1 206 600 7022

Co-Chair/Co-editor:
                    Bob Ray
                    PESA Switching Systems, Inc.
         Postal:    330-A Wynn Drive
                    Huntsville, AL 35805
                    USA
         Email:     rray@pesa.com
         Phone:     +1 256 726 9200 ext.  142

Co-editor: Menachem Dodge
                    ECI Telecom Ltd.
         Postal:    30 hasivim St.
                    Petach Tikva 49517,
                    Israel.
         Email:     mbdodge@ieee.org
         Phone:     +972 3 926 8421
        "
DESCRIPTION
    "The VDSL-LINE-MIB found in RFC 3728 defines objects for
    the management of a pair of VDSL transceivers at each end of
    the VDSL line.  The VDSL-LINE-MIB configures and monitors the
    line code independent parameters (TC layer) of the VDSL line.
    This MIB module is an optional extension of the VDSL-LINE-MIB
    and defines objects for configuration and monitoring of the
    line code specific (LCS) elements (PMD layer) for VDSL lines
    using MCM coding.  The objects in this extension MIB MUST NOT
    be used for VDSL lines using Single Carrier Modulation (SCM)
    line coding.  If an object in this extension MIB is referenced
    by a line which does not use MCM, it has no effect on the
    operation of that line.

Naming Conventions:
        Vtuc -- (VTUC) transceiver at near (Central) end of line
        Vtur -- (VTUR) transceiver at Remote end of line
        Vtu  -- One of either Vtuc or Vtur
        Curr -- Current
        LCS  -- Line Code Specific
        Max  -- Maximum
        PSD  -- Power Spectral Density
        Rx   -- Receive
        Tx   -- Transmit

Copyright (C) The Internet Society (2005).  This version
    of this MIB module is part of RFC 4070: see the RFC
    itself for full legal notices."
        REVISION "200504280000Z" --    April 28, 2005
        DESCRIPTION "Initial version, published as RFC 4070."
    ::= { transmission 229 }

vdslLineExtMCMMib OBJECT IDENTIFIER ::= { vdslExtMCMMIB 1 }
vdslLineExtMCMMibObjects OBJECT IDENTIFIER ::= {vdslLineExtMCMMib 1}

--
-- Multiple carrier modulation (MCM) configuration profile tables
--

vdslLineMCMConfProfileTable OBJECT-TYPE
    SYNTAX       SEQUENCE OF VdslLineMCMConfProfileEntry
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "This table contains additional information on multiple
        carrier VDSL lines.  One entry in this table reflects a
        profile defined by a manager which can be used to
        configure the VDSL line.

If an entry in this table is referenced by a line which
        does not use MCM, it has no effect on the operation of that
        line.

All read-create-objects defined in this table SHOULD be
        stored persistently."
    ::= { vdslLineExtMCMMibObjects  1 }

vdslLineMCMConfProfileEntry OBJECT-TYPE
    SYNTAX       VdslLineMCMConfProfileEntry
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "Each entry consists of a list of parameters that
        represents the configuration of a multiple carrier
        modulation VDSL modem."
    INDEX { vdslLineConfProfileName }
    ::= { vdslLineMCMConfProfileTable 1 }

VdslLineMCMConfProfileEntry ::=
    SEQUENCE
        {
        vdslLineMCMConfProfileTxWindowLength       Unsigned32,
        vdslLineMCMConfProfileRowStatus            RowStatus
        }

vdslLineMCMConfProfileTxWindowLength OBJECT-TYPE
    SYNTAX       Unsigned32 (1..255)
    UNITS        "samples"
    MAX-ACCESS   read-create
    STATUS       current
    DESCRIPTION
        "Specifies the length of the transmit window, counted
        in samples at the sampling rate corresponding to the
        negotiated value of N."
    REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM
    ::= { vdslLineMCMConfProfileEntry 1 }

vdslLineMCMConfProfileRowStatus OBJECT-TYPE
    SYNTAX       RowStatus
    MAX-ACCESS   read-create
    STATUS       current
    DESCRIPTION
        "This object is used to create a new row or modify or
        delete an existing row in this table.

A profile is activated by setting this object to `active'.
        When `active' is set, the system will validate the profile.

None of the columns in this row may be modified while the
        row is in the 'active' state.

Before a profile can be deleted or taken out of
        service, (by setting this object to `destroy' or
        `notInService') it must first be unreferenced
        from all associated lines."
    ::= { vdslLineMCMConfProfileEntry 2 }

vdslLineMCMConfProfileTxBandTable OBJECT-TYPE
    SYNTAX       SEQUENCE OF VdslLineMCMConfProfileTxBandEntry
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "This table contains transmit band descriptor configuration
        information for a VDSL line.  Each entry in this table
        reflects the configuration for one of possibly many bands
        with a multiple carrier modulation (MCM) VDSL line.
        These entries are defined by a manager and can be used to
        configure the VDSL line.

If an entry in this table is referenced by a line which
        does not use MCM, it has no effect on the operation of that
        line.

All read-create-objects defined in this table SHOULD be
        stored persistently."
    ::= { vdslLineExtMCMMibObjects  2 }

vdslLineMCMConfProfileTxBandEntry OBJECT-TYPE
    SYNTAX       VdslLineMCMConfProfileTxBandEntry
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "Each entry consists of a transmit band descriptor, which
        is defined by a start and a stop tone index."
    INDEX { vdslLineConfProfileName,
            vdslLineMCMConfProfileTxBandNumber }
    ::= { vdslLineMCMConfProfileTxBandTable 1 }

VdslLineMCMConfProfileTxBandEntry ::=
    SEQUENCE
        {
        vdslLineMCMConfProfileTxBandNumber           Unsigned32,
        vdslLineMCMConfProfileTxBandStart            Unsigned32,
        vdslLineMCMConfProfileTxBandStop             Unsigned32,
        vdslLineMCMConfProfileTxBandRowStatus        RowStatus
        }

vdslLineMCMConfProfileTxBandNumber OBJECT-TYPE
    SYNTAX       Unsigned32 (1..4096)
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "The index for this band descriptor entry."
    ::= { vdslLineMCMConfProfileTxBandEntry 1 }

vdslLineMCMConfProfileTxBandStart OBJECT-TYPE
    SYNTAX       Unsigned32 (1..4096)
    MAX-ACCESS   read-create
    STATUS       current
    DESCRIPTION
        "Start tone index for this band."
    REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM
    ::= { vdslLineMCMConfProfileTxBandEntry 2 }

vdslLineMCMConfProfileTxBandStop OBJECT-TYPE
    SYNTAX       Unsigned32 (1..4096)
    MAX-ACCESS   read-create
    STATUS       current
    DESCRIPTION
        "Stop tone index for this band."
    REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM
    ::= { vdslLineMCMConfProfileTxBandEntry 3 }

vdslLineMCMConfProfileTxBandRowStatus OBJECT-TYPE
    SYNTAX       RowStatus
    MAX-ACCESS   read-create
    STATUS       current
    DESCRIPTION
        "This object is used to create a new row or modify or
        delete an existing row in this table.
        A profile is activated by setting this object to `active'.
        When `active' is set, the system will validate the profile.

Each entry must be internally consistent, the Stop Tone must
        be greater than the Start Tone.  Each entry must also be
        externally consistent, all entries indexed by a specific
        profile must not overlap.  Validation of the profile will
        check both internal and external consistency.

None of the columns in this row may be modified while the
        row is in the 'active' state.

Before a profile can be deleted or taken out of
        service, (by setting this object to `destroy' or
        `notInService') it must be first unreferenced
        from all associated lines."
    ::= { vdslLineMCMConfProfileTxBandEntry 4 }

vdslLineMCMConfProfileRxBandTable OBJECT-TYPE
    SYNTAX       SEQUENCE OF VdslLineMCMConfProfileRxBandEntry
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "This table contains receive band descriptor configuration
        information for a VDSL line.  Each entry in this table
        reflects the configuration for one of possibly many bands
        with a multiple carrier modulation (MCM) VDSL line.
        These entries are defined by a manager and can be used to
        configure the VDSL line.

If an entry in this table is referenced by a line which
        does not use MCM, it has no effect on the operation of that
        line.

All read-create-objects defined in this table SHOULD be
        stored persistently."
    ::= { vdslLineExtMCMMibObjects 3 }

vdslLineMCMConfProfileRxBandEntry OBJECT-TYPE
    SYNTAX       VdslLineMCMConfProfileRxBandEntry
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "Each entry consists of a transmit band descriptor, which
        is defined by a start and a stop tone index."
    INDEX { vdslLineConfProfileName,
            vdslLineMCMConfProfileRxBandNumber }
    ::= { vdslLineMCMConfProfileRxBandTable 1 }

VdslLineMCMConfProfileRxBandEntry ::=

SEQUENCE
        {
        vdslLineMCMConfProfileRxBandNumber           Unsigned32,
        vdslLineMCMConfProfileRxBandStart            Unsigned32,
        vdslLineMCMConfProfileRxBandStop             Unsigned32,
        vdslLineMCMConfProfileRxBandRowStatus        RowStatus
        }

vdslLineMCMConfProfileRxBandNumber OBJECT-TYPE
    SYNTAX       Unsigned32 (1..4096)
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "The index for this band descriptor entry."
    ::= { vdslLineMCMConfProfileRxBandEntry 1 }

vdslLineMCMConfProfileRxBandStart OBJECT-TYPE
    SYNTAX       Unsigned32 (1..4096)
    MAX-ACCESS   read-create
    STATUS       current
    DESCRIPTION
        "Start tone index for this band."
    REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM
    ::= { vdslLineMCMConfProfileRxBandEntry 2 }

vdslLineMCMConfProfileRxBandStop OBJECT-TYPE
    SYNTAX       Unsigned32 (1..4096)
    MAX-ACCESS   read-create
    STATUS       current
    DESCRIPTION
        "Stop tone index for this band."
    REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM
    ::= { vdslLineMCMConfProfileRxBandEntry 3 }

vdslLineMCMConfProfileRxBandRowStatus OBJECT-TYPE
    SYNTAX       RowStatus
    MAX-ACCESS   read-create
    STATUS       current
    DESCRIPTION
        "This object is used to create a new row or modify or
        delete an existing row in this table.

A profile is activated by setting this object to `active'.
        When `active' is set, the system will validate the profile.
        Each entry must be internally consistent, the Stop Tone must
        be greater than the Start Tone.  Each entry must also be
        externally consistent, all entries indexed by a specific

profile must not overlap.  Validation of the profile will
        check both internal and external consistency.

None of the columns in this row may be modified while the
        row is in the 'active' state.

vdslLineMCMConfProfileTxPSDTable OBJECT-TYPE
    SYNTAX       SEQUENCE OF VdslLineMCMConfProfileTxPSDEntry
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "This table contains transmit PSD mask descriptor
        configuration information for a VDSL line.  Each entry in
        this table reflects the configuration for one tone within
        a multiple carrier modulation (MCM) VDSL line.  These
        entries are defined by a manager and can be used to
        configure the VDSL line.

If an entry in this table is referenced by a line which
        does not use MCM, it has no effect on the operation of that
        line.

All read-create-objects defined in this table SHOULD be
        stored persistently."
    ::= { vdslLineExtMCMMibObjects 4 }

vdslLineMCMConfProfileTxPSDEntry OBJECT-TYPE
    SYNTAX       VdslLineMCMConfProfileTxPSDEntry
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "Each entry consists of a transmit PSD mask descriptor,
        which defines the power spectral density (PSD) for a tone."
    INDEX { vdslLineConfProfileName,
            vdslLineMCMConfProfileTxPSDNumber }
    ::= { vdslLineMCMConfProfileTxPSDTable 1 }

VdslLineMCMConfProfileTxPSDEntry ::=
    SEQUENCE
        {
        vdslLineMCMConfProfileTxPSDNumber            Unsigned32,
        vdslLineMCMConfProfileTxPSDTone              Unsigned32,
        vdslLineMCMConfProfileTxPSDPSD               Unsigned32,
        vdslLineMCMConfProfileTxPSDRowStatus         RowStatus
        }

vdslLineMCMConfProfileTxPSDNumber OBJECT-TYPE
    SYNTAX       Unsigned32 (1..4096)
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "The index for this mask descriptor entry."
    ::= { vdslLineMCMConfProfileTxPSDEntry 1 }

vdslLineMCMConfProfileTxPSDTone OBJECT-TYPE
    SYNTAX       Unsigned32 (1..4096)
    MAX-ACCESS   read-create
    STATUS       current
    DESCRIPTION
        "The tone index for which the PSD is being specified."
    REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM
    ::= { vdslLineMCMConfProfileTxPSDEntry 2 }

vdslLineMCMConfProfileTxPSDPSD OBJECT-TYPE
    SYNTAX       Unsigned32
    UNITS        "0.5dBm/Hz"
    MAX-ACCESS   read-create
    STATUS       current
    DESCRIPTION
        "Power Spectral Density level in steps of 0.5dBm/Hz with
        an offset of -140dBm/Hz."
    REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM
    ::= { vdslLineMCMConfProfileTxPSDEntry 3 }

vdslLineMCMConfProfileTxPSDRowStatus OBJECT-TYPE
        SYNTAX       RowStatus
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "This object is used to create a new row or modify or
        delete an existing row in this table.

A profile is activated by setting this object to `active'.
        When `active' is set, the system will validate the profile.

None of the columns in this row may be modified while the
        row is in the 'active' state.

Before a profile can be deleted or taken out of

service, (by setting this object to `destroy' or
        `notInService') it must be first unreferenced
        from all associated lines."
    ::= { vdslLineMCMConfProfileTxPSDEntry 4 }

vdslLineMCMConfProfileMaxTxPSDTable OBJECT-TYPE
    SYNTAX       SEQUENCE OF VdslLineMCMConfProfileMaxTxPSDEntry
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "This table contains transmit maximum PSD mask descriptor
        configuration information for a VDSL line.  Each entry in
        this table reflects the configuration for one tone within
        a multiple carrier modulation (MCM) VDSL modem.  These
        entries are defined by a manager and can be used to
        configure the VDSL line.

If an entry in this table is referenced by a line which
        does not use MCM, it has no effect on the operation of that
        line.

All read-create-objects defined in this table SHOULD be
        stored persistently."
    ::= { vdslLineExtMCMMibObjects 5 }

vdslLineMCMConfProfileMaxTxPSDEntry OBJECT-TYPE
    SYNTAX       VdslLineMCMConfProfileMaxTxPSDEntry
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "Each entry consists of a transmit PSD mask descriptor,
        which defines the maximum power spectral density (PSD)
        for a tone."
    INDEX { vdslLineConfProfileName,
            vdslLineMCMConfProfileMaxTxPSDNumber }
    ::= { vdslLineMCMConfProfileMaxTxPSDTable 1 }

VdslLineMCMConfProfileMaxTxPSDEntry ::=
    SEQUENCE
        {
        vdslLineMCMConfProfileMaxTxPSDNumber            Unsigned32,
        vdslLineMCMConfProfileMaxTxPSDTone              Unsigned32,
        vdslLineMCMConfProfileMaxTxPSDPSD               Unsigned32,
        vdslLineMCMConfProfileMaxTxPSDRowStatus         RowStatus
        }

vdslLineMCMConfProfileMaxTxPSDNumber OBJECT-TYPE
    SYNTAX       Unsigned32 (1..4096)
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "The index for this band descriptor entry."
    ::= { vdslLineMCMConfProfileMaxTxPSDEntry 1 }

vdslLineMCMConfProfileMaxTxPSDTone OBJECT-TYPE
    SYNTAX       Unsigned32 (1..4096)
    MAX-ACCESS   read-create
    STATUS       current
    DESCRIPTION
        "The tone index for which the PSD is being specified.
         There must not be multiple rows defined, for a particular
         profile, with the same value for this field."
    REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM
    ::= { vdslLineMCMConfProfileMaxTxPSDEntry 2 }

vdslLineMCMConfProfileMaxTxPSDPSD OBJECT-TYPE
    SYNTAX       Unsigned32
    UNITS        "0.5dBm/Hz"
    MAX-ACCESS   read-create
    STATUS       current
    DESCRIPTION
        "Power Spectral Density level in steps of 0.5dBm/Hz with
        an offset of -140dBm/Hz."
    REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM
    ::= { vdslLineMCMConfProfileMaxTxPSDEntry 3 }

vdslLineMCMConfProfileMaxTxPSDRowStatus OBJECT-TYPE
    SYNTAX       RowStatus
    MAX-ACCESS   read-create
    STATUS       current
    DESCRIPTION
        "This object is used to create a new row or modify or
        delete an existing row in this table.
        A profile is activated by setting this object to `active'.
        When `active' is set, the system will validate the profile.
        There must be only one entry in this table for each tone
        associated with a specific profile.  This will be checked
        during the validation process.

None of the columns in this row may be modified while the
        row is in the 'active' state.

vdslLineMCMConfProfileMaxRxPSDTable OBJECT-TYPE
    SYNTAX       SEQUENCE OF VdslLineMCMConfProfileMaxRxPSDEntry
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "This table contains maximum receive PSD mask descriptor
        configuration information for a VDSL line.  Each entry in
        this table reflects the configuration for one tone within
        a multiple carrier modulation (MCM) VDSL modem.  These
        entries are defined by a manager and can be used to
        configure the VDSL line.

If an entry in this table is referenced by a line which
        does not use MCM, it has no effect on the operation of that
        line.

All read-create-objects defined in this table SHOULD be
        stored persistently."
    ::= { vdslLineExtMCMMibObjects 6 }

vdslLineMCMConfProfileMaxRxPSDEntry OBJECT-TYPE
    SYNTAX       VdslLineMCMConfProfileMaxRxPSDEntry
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "Each entry consists of a transmit PSD mask descriptor,
        which defines the power spectral density (PSD) for a
        tone."
    INDEX { vdslLineConfProfileName,
            vdslLineMCMConfProfileMaxRxPSDNumber }
    ::= { vdslLineMCMConfProfileMaxRxPSDTable 1 }

VdslLineMCMConfProfileMaxRxPSDEntry ::=
    SEQUENCE
        {
        vdslLineMCMConfProfileMaxRxPSDNumber            Unsigned32,
        vdslLineMCMConfProfileMaxRxPSDTone              Unsigned32,
        vdslLineMCMConfProfileMaxRxPSDPSD               Unsigned32,
        vdslLineMCMConfProfileMaxRxPSDRowStatus         RowStatus
        }

vdslLineMCMConfProfileMaxRxPSDNumber OBJECT-TYPE
    SYNTAX       Unsigned32 (1..4096)
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "The index for this band descriptor entry."
    ::= { vdslLineMCMConfProfileMaxRxPSDEntry 1 }

vdslLineMCMConfProfileMaxRxPSDTone OBJECT-TYPE
    SYNTAX       Unsigned32 (1..4096)
    MAX-ACCESS   read-create
    STATUS       current
    DESCRIPTION
        "The tone index for which the PSD is being specified.
         There must not be multiple rows defined, for a particular
         profile, with the same value for this field."
    REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM
    ::= { vdslLineMCMConfProfileMaxRxPSDEntry 2 }

vdslLineMCMConfProfileMaxRxPSDPSD OBJECT-TYPE
    SYNTAX       Unsigned32
    UNITS        "0.5dBm/Hz"
    MAX-ACCESS   read-create
    STATUS       current
    DESCRIPTION
        "Power Spectral Density level in steps of 0.5dBm/Hz with
        an offset of -140dBm/Hz."
    REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM
    ::= { vdslLineMCMConfProfileMaxRxPSDEntry 3 }

vdslLineMCMConfProfileMaxRxPSDRowStatus OBJECT-TYPE
    SYNTAX       RowStatus
    MAX-ACCESS   read-create
    STATUS       current
    DESCRIPTION
        "This object is used to create a new row or modify or
        delete an existing row in this table.

A profile is activated by setting this object to `active'.
        When `active' is set, the system will validate the profile.
        There must be only one entry in this table for each tone
        associated with a specific profile.  This will be checked
        during the validation process.

None of the columns in this row may be modified while the
        row is in the 'active' state.

-- conformance information

vdslLineExtMCMConformance OBJECT IDENTIFIER ::=
                 { vdslLineExtMCMMib 2 }
vdslLineExtMCMGroups OBJECT IDENTIFIER ::=
                 { vdslLineExtMCMConformance 1 }
vdslLineExtMCMCompliances OBJECT IDENTIFIER ::=
                 { vdslLineExtMCMConformance 2 }

vdslLineExtMCMMibCompliance MODULE-COMPLIANCE
    STATUS  current
    DESCRIPTION
        "The compliance statement for SNMP entities which
        manage VDSL interfaces."
    MODULE  -- this module
    MANDATORY-GROUPS
    {
        vdslLineExtMCMGroup
    }
    ::= { vdslLineExtMCMCompliances 1 }

-- units of conformance

vdslLineExtMCMGroup OBJECT-GROUP
        OBJECTS
            {
            vdslLineMCMConfProfileTxWindowLength,
            vdslLineMCMConfProfileRowStatus,
            vdslLineMCMConfProfileTxBandStart,
            vdslLineMCMConfProfileTxBandStop,
            vdslLineMCMConfProfileTxBandRowStatus,
            vdslLineMCMConfProfileRxBandStart,
            vdslLineMCMConfProfileRxBandStop,
            vdslLineMCMConfProfileRxBandRowStatus,
            vdslLineMCMConfProfileTxPSDTone,
            vdslLineMCMConfProfileTxPSDPSD,
            vdslLineMCMConfProfileTxPSDRowStatus,
            vdslLineMCMConfProfileMaxTxPSDTone,
            vdslLineMCMConfProfileMaxTxPSDPSD,
            vdslLineMCMConfProfileMaxTxPSDRowStatus,
            vdslLineMCMConfProfileMaxRxPSDTone,
            vdslLineMCMConfProfileMaxRxPSDPSD,
            vdslLineMCMConfProfileMaxRxPSDRowStatus
            }
         STATUS     current
         DESCRIPTION
             "A collection of objects providing configuration

information for a VDSL line based upon multiple
             carrier modulation modem."
     ::= { vdslLineExtMCMGroups 1 }

END